183 Wyniki
Wyświetl wyniki:
Sortuj według:
Trajektorie - Wektorowa reprezentacja naprężeń głównych
Jak wyświetlić wyniki naprężeń głównych wraz z kierunkami jako trajektorie w programie RFEM 6?
Analiza stateczności zgodnie z EN 1999-1-1
Czy możliwe jest przeprowadzenie analizy stateczności zgodnie z EN 1999-1-1 w RSECTION 1?
Analiza stateczności zgodnie z EN 1993-1-1
Czy w RSECTION 1 można przeprowadzić analizy stateczności zgodnie z EN 1993-1-1?
Kontakt między powierzchniami
Czy program RFEM 5 uwzględnia kontakt powierzchniowy?
Analiza statyczna naprężeń różnicowych - naprężenie-odkształcenie
Dlaczego naprężenia dostępne w Analizie statycznej różnią się od tego w rozszerzeniu Analiza naprężeniowo-odkształceniowa?
Warunki projektowe stateczności ze skręcaniem
Podczas wymiarowania stali w programie RFEM 6 lub RSTAB 9 otrzymuję ostrzeżenie, że skręcanie jest pominięte w obliczeniach stateczności. Jaka jest przyczyna i jak mogę uniknąć komunikatu ostrzegawczego?
Obciążenie wydłużenia muru izotropowego | Plastyczne
Czy można odnieść się do poprzecznego rozkładu obciążenia w przypadku izotropowego modelu materiałowego? | Mur | mieć wpływ plastyczny?
Naprężenia jednostkowe
Czy mogę oszacować, które minimalne przekroje należy zastosować przed rozpoczęciem projektowania modelu?
Przekrój efektywny
Czy mogę obliczyć efektywne właściwości przekroju za pomocą RSECTION?
elektrownie i przenośniki
Jakich programów mogę użyć do obliczenia elektrowni i konstrukcji przenośników?
Rusztowania i konstrukcje stelażowe
Wyszukujemy program do rusztowań i konstrukcji stelażowych. Czy nadaje się do tego program Dlubal Software?
Obliczanie stalowych konstrukcji hydraulicznych
Czy mogę analizować i wymiarować stalowe konstrukcje hydrauliczne za pomocą programów Dlubal?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programy dla konstrukcji stalowych
Jakie programy i rozszerzenia są odpowiednie do obliczeń i wymiarowania konstrukcji stalowych?
Jak utworzyć bryłę kontaktową między dwiema powierzchniami w programie RFEM?
Jak utworzyć bryłę kontaktową między dwiema powierzchniami w programie RFEM?
Momenty oporu względem osi y, z
W jaki sposób obliczane są momenty oporu względem osi y, z w PRZEKRÓJ 1, CIENIOWANIE i GRUBOŚĆ?
Ustawianie odkształceń na 0
Jak ustawić odkształcenia z PO/KO lub etapu budowy na 0?
Historia wyników z obszarem wygładzania w RFEM 6
Jak wstawić obszar wygładzania/linię wygładzania do profilu wyników w RFEM 6?
Spoiny w RFEM 6
Na schodach o skomplikowanej geometrii często trudno jest zweryfikować spoiny metodami analitycznymi. Jak można to zrobić w programie RFEM?
Sprężyna deplanacyjna i naprężenia deplanacyjne
Jak mogę zdefiniować sprężystość deplanacyjną lub naprężenie deplanacyjne?
Wykorzystanie
Naprężenie graniczne jest aktywne, ale mojego współczynnika naprężeń „nie można opisać” w dodatku Analiza naprężeniowo-odkształceniowa. Jaki może być powód?
- 005235
- RFEM 6
- Projektowanie konstrukcji betonowych RFEM 6
-
- Projektowanie konstrukcji betonowych RSTAB 9
- RSTAB 9
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
- Konstrukcje betonowe
- Konstrukcje stalowe
- Konstrukcje drewniane